Recent Posts

Pages: 1 2 3 4 5 6 7 8 9 10
1
Stars Want to Sell/Want to Buy / Re: Powder magazine
« Last post by FOR_Star on December 16, 2017, 05:24:27 PM »
Ditto on Bruce.  He just did one for me.  I sent him the part I had, & he supplied the rest.  Looks perfect.

Email or call him & he'll get you squared away.

http://www.starmachineworks.com/
2
Stars Want to Sell/Want to Buy / Re: Powder magazine
« Last post by NYKenn on December 16, 2017, 04:09:22 PM »
Contact Bruce Williams on this site, member:     RBWillNJ

or his Star Reloaders website.
3
Stars Want to Sell/Want to Buy / Powder magazine (No longer needed)
« Last post by Buckhunter on December 16, 2017, 02:51:51 PM »
 I need a clear plastic Powder Magazine Tube to replace a broken
 tube or a complete Plastic Powder Magazine Tube for my Star Reloader.
 E-mail me at:  buckhamman     at      comcast     dot     net

 Thanks, Buckhunter

  Bruce Williams is building me a Powder Magazine Tube, I have been
  buying and selling with Bruce for years and since he acquired the Star
  parts from California he is the man to go to for star parts. When the
  guy in California had the parts I could never get in touch with him,
  Bruce is the opposite as he answers right away.
  Thanks everyone for your input. I no longer need a Powder Magazine.
 
  Buckhunter
4
Stars Want to Sell/Want to Buy / Re: MA System Bullet Feeder
« Last post by varmintpopper on December 15, 2017, 08:04:33 PM »
The MA systems Bullet Feeder in action.

http://www.youtube.com/watch?v=1c3Egi8LvdQ&feature=youtu.be

Good Shooting

Lindy

5
Star Reloaders / Re: MA systems bullet feeder
« Last post by varmintpopper on December 15, 2017, 12:01:04 PM »
Perhaps this video will work. MA systems bullet feeder on a Star reloader.


http://www.youtube.com/watch?v=1c3Egi8LvdQ&feature=youtu.be

Good Shooting

Lindy
6
Stars Want to Sell/Want to Buy / Re: Sale of tool
« Last post by rbwillnj on December 07, 2017, 11:22:46 PM »
PM Sent

Bruce Williams
7
Stars Want to Sell/Want to Buy / Sale of tool
« Last post by Darren F Wallis on December 07, 2017, 10:37:11 PM »
I have a star reloader of course and I would like to sell it. Unfortunately I do not know how to describe it in perfect detail. The press itself has a .38special die plate with all dies installed. Surface rust but not to unserviceable state, slide unaffected. Rust confined to arm, spring rod and tool head containing dies. A 45acp tool head also is available and it was stored properly, exhibiting no rust and all stations contain dies. Upon viewing this forum I realize that I left the case feeding parts behind and can not retrieve them. How to post pictures of anything, anywhere on a computer has not seemed important enough to know how to do it, yet. I'll try to find someone to help.
I need a .458-9" sizing die for my Star lube & sizing tool and I would like to end up with a new Redding turret press.
8
Star Reloaders / Re: MA systems bullet feeder
« Last post by varmintpopper on December 07, 2017, 05:35:11 PM »
Hi 4-star
There is a direction valve shown in the second Pic down that is located near the tool head spring anchor#57 that reverses the air pressure to the pneumatic
cylinder and the bullet holder tries to retract away from the machine but is cought on a step , when the tool head comes down it pushes the bullet holder down and off the step allowing it to retract and pick up another bullet.
Clear as a bell,, Right.

Good Shooting

Lindy
9
Star Reloaders / Re: MA systems bullet feeder
« Last post by FOR_Star on December 07, 2017, 01:23:29 PM »
Thanks.  Very interesting pictures.
What causes the bullet holder to retract before the seating die hits it?
10
Star Reloaders / Re: MA systems bullet feeder
« Last post by varmintpopper on December 07, 2017, 12:23:08 AM »
more Pic's
Pages: 1 2 3 4 5 6 7 8 9 10