Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - tguntrader

Pages: 1
1
Stars Want to Sell/Want to Buy / Powder bar
« on: January 25, 2014, 09:48:37 am »
Any one got a hoag adj, bar for sale. tguntrader

2
Loading Data & Reloading Procedures / 38 super lightweight colt
« on: January 17, 2014, 04:29:02 pm »
Can any that has done the leg work tell me what  would be a good load to shoot in this gun  that would not  beat it up to bad that I can load on my star with a 00 slide?                                thanks  tguntrader

3
Star Lubricator & Resizers / Die Tool
« on: February 08, 2012, 08:21:36 pm »
Guy,s Is important to have  a tool to remove dies, to save the dies, Are can you do it the old fashion way with a round piece of wood?

            Thanks Tguntrader

4
Star Reloaders / 9mm loader
« on: January 27, 2012, 05:13:48 pm »
First time I had this problem?
  I took my 9mm press apart over the winter, Just run my first shells to check press, In the middle of the cart./ i have a s back mule look, How far should the seater die be off the shell plate to get best cart,s?

                              Tguntrader

5
Star Reloaders / Shell Plates and Dies
« on: February 28, 2011, 05:47:00 pm »
Hi Guy,s
            Just got back from gun show in louisville Ky, I saw one star machine and it sold in first 20 Min. of show 45 Acp. In universial. for $ 650.00. I am now loading 38 super thanks to dave, Rich, and bruce. Dies fron dave works great, shell plate from rich works great, also a adj. bar from rich is very good work/ powder tubes from bruce is the best also. along with a bar and bushings from bruce. Bill also sent me a lot of small parts I needed.
 all I can say is keep up the good work we need you guy,s to keep oure machines runing.

                                 Thanks tguntrader

6
Star Reloaders / Dies from fc60
« on: February 28, 2011, 11:01:10 am »
Hi Guy,s Just got my 38 super dies from dave, Talking about great work/ They are great> they look like the old stars. dies. If any one need dies better get in touch with him these are  every prof. done.

                         Thanks dave  tguntrader

7
Star Reloaders / star {pure at heart)
« on: February 22, 2011, 10:23:00 am »
Hi Guy,s

         What does every one think about cutting out the last station so you can put a  case kicker on  regular loader ?

                  Thanks Tguntrader

8
Star Reloaders / Part #35?
« on: February 13, 2011, 08:35:48 pm »
Tguntrader,

             On part # 35 Primer follower rod, can any one tell me where to get a replacement part for the rod that goes on the end, also what it is made of.

                   Thanks in advance
                     Tguntrader

9
Star Reloaders / primer pin
« on: February 09, 2011, 05:08:53 pm »
Tguntrader.

               I have a question about the adj. on the primer punch pin, when setting this pin  should it come up past the plug and if how mutch.?

                                     THanks In advance. tguntrader

10
Loading Data & Reloading Procedures / How to set dies
« on: January 24, 2011, 01:56:45 pm »
Should you have any cam over on the lifetime dies on a star machine? I don,t want to do any harm to the dies.

                                             Thanks tguntrader

11
Loading Data & Reloading Procedures / Loading bar
« on: November 18, 2009, 10:31:50 am »
I have a star 9mm. loader. It has a w231 bar that is marked 4.8 Gr. Is that to hot for a browning hi power 9mm.  Is there any new power that would work in this same bar. New member help?

                                             Thanks tguntrader

Pages: 1