Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - rbwillnj

61
Star Reloaders / Re: Detent Ball - How much spring tension?
« on: December 29, 2020, 11:16:10 pm »
As Dave says, just screw it in until it binds or stops.   On most machines the brass plug when screwed in as far as it goes, will sit proud of the steel base.  It won't hurt anything if you don't screw it in that far.  You don't need much tension on the spring.   Just keep the hole clean so the ball travels freely.   Be careful not to scratch up the sides of the hole.

Bruce Williams

62
Star Reloaders / Re: Changing a 45acp to 45LC
« on: December 28, 2020, 12:53:12 pm »
My personal 45 Colt setup includes a Lifetyme die where the "ACP" is over-stamped with "Colt".   I think it was done at the factory.    Maybe when they did the QC check on the size of the carbide ring they found it was oversized for 45 ACP. ??

63
Stars Want to Sell/Want to Buy / Re: WTS 40 S&W Shell Plate and Die Set
« on: December 23, 2020, 09:00:52 am »
David,   I sent you an invoice and payment instructions via email.

64
Stars Want to Sell/Want to Buy / Re: WTS 40 S&W Shell Plate and Die Set
« on: December 22, 2020, 05:29:28 pm »
Yes, still available.


65
Star Reloaders / Re: .223 Super Stars Conversions
« on: December 22, 2020, 10:49:07 am »
No, not carbide, but most bottleneck rifle dies are not carbide and even those that are still recommend (require) using case lube.  I'm pretty sure that Dillon had RCBS make the dies for the Super Star Kit.

66
Star Reloaders / Re: .223 Super Stars Conversions
« on: December 15, 2020, 04:53:43 pm »
Green Frog,

It's definitely for a Universal,   Part of the kit is a couple special shell locator straps.

NYKenn,

No idea but I'm thinking late 70's, or very early 80's.   Here is a link to Dillon's about page.   https://www.dillonprecision.com/about-us.html

Bruce Williams

67
Star Reloaders / Re: .223 Super Stars Conversions
« on: December 14, 2020, 08:46:31 am »
Don't know if it's still there, but on the about page of Dillon's website (while Mike was still alive) it said he sold about 100 of the kits.    Some of the parts, like the powder magazine and powder slide were were available separately.    I accumulated five of the kits, but the first one took me forever, getting pieces here and there.

Bruce Williams

68
Star Reloaders / Re: New member, with a newly-acquired Star
« on: December 09, 2020, 11:56:01 am »
Actually,  I have sold a number of rebuilt machines to customers in Australia and parts to others.  We have a number of members on the forum from down under.   Outside of the USA, I see the most Stars in Australia and in the Scandinavian countries.   

Florey55,

Send me an email to the address on the card below and I will send you a quote for the parts I see missing on your machine.    Please include your shipping address.

Bruce Williams

69
Star Reloaders / Re: Star Adapter
« on: December 07, 2020, 06:02:30 pm »
I still sell them, but the brass version is out of stock.  Hope to make more this winter.   The aluminum version is in stock.

https://starreloaders.com/forum/index.php?topic=1735.0


Bruce Williams

PS  I have sold a lot of them, so maybe more will show up on eBay.

70
Star Reloaders / Re: Taper crimp die post end type
« on: October 23, 2020, 01:28:42 pm »
In older tool heads, there is a 3/8" hole in the tool head at the taper crimp station.....which is the station where you remove the finished round.   On newer tool heads, the 3/8" hole is replaced with an 11/16"-24 threaded hole for a threaded taper crimp die.

71
Star Reloaders / Re: Taper crimp die post end type
« on: October 22, 2020, 10:10:07 pm »
According to the attached letter from the American Rifleman,  John Giles invented it, and it was manufactured by Heatbath Corp.   Star made their own version.

72
I noticed that you have it simultaneously listed on GunBroker.com

73
Star Reloaders / Re: Hulme case feeder dimensions
« on: October 15, 2020, 08:24:21 pm »
You probably have an older model Hulme.   The hole in the top should be 9/16", and later models have a T-Slot in the bottom that is 5/8" wide (a bit narrower on transition models).   If your case feeder doesn't have the T Slot, you won't be able to use if for anything bigger than 41 Magnum.

74
Star Reloaders / Re: New member
« on: October 03, 2020, 09:01:43 am »
Congratulations.   If you need any help getting things going, there are lots of folks on the forum who can help.

75
Star Reloaders / Re: Moon Indexer Instructions
« on: September 17, 2020, 07:40:12 pm »
Thanks to all,  A copy on it's way to me from Steve.   I often get questions so I wanted to get a copy for my files.

Thanks,
Bruce