Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - GeraldChainsaw

Pages: 1 2 »
1
Star Reloaders / charge bars
« on: January 04, 2018, 06:12:11 pm »
can someone give me the dimensions for a charge bar?,  thickness, width and length,   are they all 5/16ths thick?  thanks    jerry

2
Star Reloaders / threads
« on: December 01, 2017, 05:54:24 pm »
does any one know?,  thread size on star dies compared to maybe RCBS,  thanks

3
Star Reloaders / question
« on: November 30, 2017, 05:39:48 pm »
hi all,   what i want to know is,  with the right dies can u reload 45acp using a 44 mag shell plate?

4
Star Reloaders / difference
« on: November 15, 2017, 10:13:28 pm »
ihave a bad memory,    tell me again the diff between a universal and a progressive,    this time i'll write it down,  thanks   jerry

5
Stars Want to Sell/Want to Buy / primer pickup tube
« on: January 04, 2017, 09:48:46 am »
hi,  I need a small primer pickup tube,  anyone have one?,  if so,  let me know how much,  thanks    jerry

6
Survey Says... / ;part;s list
« on: December 25, 2016, 10:15:42 pm »
where can I get a ;parts list?,   someone asked me about #51 & #35, what are they on a star rreloading press,      thanks    jerry

7
Stars Want to Sell/Want to Buy / clone hulme case feeders
« on: April 25, 2016, 07:01:37 pm »
i've made 7 clone hulme case feeders,  use for 38spl and 45 acp,  $90 free shipping,   i used black deltrin plastic instead of the white,  c picture.     u can reach me at,       jerrywmalcolm at aol dot com

8
Stars Want to Sell/Want to Buy / powder shut off valve
« on: February 25, 2016, 05:22:26 pm »
ok,   i've made 8 more new powder shut off valves with new clear plastic 11 1/2" long, new top,   using brass 9/16-27tpi,    asking $55 + shipping,     jerrywmalcolm at aol dot com

9
Survey Says... / spiders
« on: November 14, 2015, 08:53:11 am »
when people are logged on,  or visitors,  what does the spiders mean?

10
Star Reloaders / difference
« on: October 05, 2015, 04:58:23 pm »
can someone tell me the diff between a universal and a progressive reloading press?,   give me a picture if u can,  thanks   jerry

11
Star Reloaders / bought a star
« on: May 05, 2015, 03:39:55 pm »
hi,  today i bought a star from a old guy,  hasn't been used for years,  so the usual cleanup,  but it has 2 heads,  1 for 38 the other 45,  so i have a few questions,   since i already have a set up for 38,  i'm going to set this up for 45.    it has a hulme case feeder like i havn't seen before,  and stamped hulme firearm service,  in a cut away type piece,  half the size of the ones we use now,  is there a way to find out what year this might have been made?, ,  and as for setting the primers,  i know the primer arm has to be changed because of size,  but can i use the same set up that pushes in the primer or does that have to be changed also?,  i'm pretty sure this is a universal but whaen i run the cases thru at the last stage i dosen't drop thru like the 38,  do i have to make a special extractor ,  thats all the questions for now,  i'm sure there will be more later,  thanks   jerry

12
Stars Want to Sell/Want to Buy / hulme case feeders (clones)
« on: April 20, 2015, 09:47:01 am »
i have made 10 more case feeders,   but instead of white they are black, still made of delrin industrial plastic,   the spring push rod is white delrin plastic,  fits a star or Phelps press,  set up for 45acp or 38spl, or 357 mag,  $85 + shipping,  if not satified send back and i'll return your money - shipping,  jerry

13
Survey Says... / mini drill/mill machine
« on: February 04, 2015, 04:11:30 am »
hi,  anyone have or use a small milling machine,?,  looking for one,  around 7 or 800,  any suggestions,  thanks  jerry

14
Survey Says... / arm size
« on: January 30, 2015, 06:21:48 pm »
this could b in the wrong spot,   if it is,  point me in the right direction.    I need the diam of the main spring arm above the nut,  I think its 5/16ths,  would someone check to let me know,  thanks   jerry

15
Stars Want to Sell/Want to Buy / have made 10 more for sale
« on: January 18, 2015, 10:32:59 am »
i made 10 clone hulme case feeders,    made of delrin industrial plastic,  set up for 45acp, 38spl or 357mag,           $85 + shipping,  and if u don't like it,  send it back and i'll give u your money - shipping b;avck,   jerry

Pages: 1 2 »
anything